Allen-Bradley 2-D Uživatelský manuál Strana 47
- Strana / 92
- Tabulka s obsahem
- ŘEŠENÍ PROBLÉMŮ
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Parameters and Programming 5-9
46 [Input Mode]
Configures the TB3 control inputs for various 3-wire or 2-wire control schemes.
Also enables/disables the program keypad module input control.
Settings: 0 = 3-wire control
➊
1 = 2-wire control
➊
2 = Program Keypad Module control
➊
3 = Momentary Run Forward/ Run Reverse control
➊
4 = 2-wire Accel/Decel control
5 = 2-wire Coast to Rest control
➊
6 = 2-wire TB3 Control/Keypad or Communication control
7 = 2-wire Frequency Select control
8 = 2-wire Preset control
➋
9 = 2-wire PI control
➋
➊
A contact closure on TB3 Terminal 7 and 8 is required for the drive to respond
to a Run command.
➋
Only available in Analog Signal Follower model.
See Chapter 2 for wiring diagrams and descriptions of settings.
0/9 Numeric
Value
0
47 [Output Configure]
Configures the TB3 relay output functionality.
0/10 Numeric
Value
0
48 [Output Threshold]
Determines the on/off point for the TB3 output relay when P47 - [Output Configure]
is set to 6, 7, 8, and 10.
Setting Ranges
6 0 to 240 Hz
7 0 to 180%
8 0 to 815 Volts
10 0 to 180˚
0/815 Numeric
Value
0
Program Group
No. Parameter Name/Description
Min./Max.
Range
Units
Factory
Default
Important: This parameter cannot be programmed while
the drive is running. In addition, power must
be cycled or P56 - [Reset Function] must be
set to 2 for the change to take effect.
Setting Output Changes State When . . .
0 Drive Ready/Faulted Energized and returns to shelf state when power is
removed or a fault occurs.
1 At Frequency Drive reaches commanded frequency.
2 Motor Running The motor is receiving power from drive.
3 Reverse Drive is commanded to run in the reverse direction.
4 Motor Overload A motor overload condition exists.
5 Ramp Regulated The ramp regulator is modifying the programmed accel/
decel times to avoid an overcurrent or overvoltage fault
from occurring.
6 Above Frequency The drive exceeds the frequency value set in
P48 - [Output Threshold].
7 Above Current Drive exceeds the value set in P48 - [Output Threshold].
Important: Value for P48 - [Output Threshold] must be
entered in percent of drive rated output current.
8 Above DC Bus Voltage Drive exceeds the DC bus voltage value set in
P48 - [Output Threshold].
9 Retries Exhausted Number of retries for P50 - [Restart Tries] is exceeded.
10 Above Power Factor
Angle
Power Factor angle exceeds the value set in
P48 - [Output Threshold].
- 160 SSC™ 1
- Variable Speed 1
- (Series C) 1
- Important User Information 2
- Series C Summary of Changes 3
- Table of Contents 5
- Getting Started 7
- 160 -AA02 N SF1 P1 8
- 160-AA02NSF1P1 9
- Standard Drive Features 10
- Optional Drive Features 11
- End of Chapter 12
- Installation and Wiring 13
- Power Wiring 14
- Specifications 15
- Terminal Block Wiring 15
- Motor Branch Circuit Analysis 16
- Input Power Conditioning 18
- Motor Cable Types 18
- Reflected Wave Protection 19
- Capacitive Current Coupling 20
- Nm (lb in) 21
- Wiring Diagram Key 22
- 2-12 Installation and Wiring 24
- Installation and Wiring 2-17 29
- Analog Frequency Sources 30
- Preset Frequency Sources 31
- Internal Frequency Source 32
- Program Keypad Module 33
- Key Functions 34
- Program Keypad Module 3-3 35
- Installation 36
- Start-Up 37
- 4-2 Start-Up 38
- Parameters and Programming 39
- Important Reset Actions 40
- Programming Example 40
- Display Group (Read Only) 43
- 0/48 Numeric Value 43
- Program Group Parameters 44
- % [Base Frequency] 45
- % [Base Voltage] 45
- 46 [Input Mode] 47
- 47 [Output Configure] 47
- 48 [Output Threshold] 47
- 49 [PWM Frequency] 48
- 50 [Restart Tries] 48
- 51 [Restart Time] 48
- 52 [DB Enable] 48
- 53 [S-Curve] 49
- 54 [Clear Fault] 49
- 55 [Memory Probe Address] 49
- 56 [Reset Functions] 49
- Preset Speed Model Only 50
- Signal Follower 50
- Model Only 50
- Settings: 52
- 81 [PI Proportional Gain] 53
- 82 [PI Integral Gain] 53
- 83 [PI Process Reference] 53
- 84 [PI Dead Band] 53
- 160 PI Control Setup 54
- Troubleshooting 57
- Problem Corrective Action 59
- 6-4 Troubleshooting 60
- CSA 22.2 62
- Specifications A-3 63
- End of Appendix 64
- Accessories and Dimensions 65
- Accessory Dimensions 66
- Line Filters Figure B.3 67
- MADE IN U.S.A 68
- 29 ➊ 69
- Drive Dimensions 70
- 5.5 (0.22) 72
- Mounting Holes—2 Places 72
- CE Conformity 75
- Shielded Enclosure 76
- Cable Clamps 77
- Motor Cable 77
- Control Wiring TB3 78
- Ground Terminal – PE 78
- CE Conformity C-5 79
- Index-10 90
Související produkty a manuály pro Čtečky čárových kódů Allen-Bradley 2-D
(96 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.044 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce