Allen-Bradley 2-D Uživatelský manuál Strana 106
- Strana / 172
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Programming
5-37
This group of parameters contains the programming options for digital and analog drive outputs.
Output
Configura-
tion
[O
u
tp
u
t
1 Confi
g]
Parameter # 90 Factory Default “Faulted“
[O
u
tp
u
t
1 Confi
g]
Parameter Type Read & Write
This parameter sets the condition that actuates the relay
a 2, ermi a 9 a 10.
Units Text Settings ‘‘At Speed”
Output closes when drive reaches [Freq Command].
Th
i
s p
arame
t
er
s
e
ts th
e
cond
i
t
i
on th
a
t
a
ctu
a
t
e
s th
e
re
l
a
y
output at TB2, terminals 9 and 10.
‘‘Above Freq”
Output closes when drive exceeds value set in
[Above Freq Val].
‘‘Running”
Output closes when drive is running.
‘‘Faulted”
Output closes when drive is faulted.
‘‘Alarm”
Output closes when the drive reaches hardware
current limit, software current limit, overvoltage, line
loss or 4-20 mA loss.
‘‘Above Curr”
Output closes when current exceeds value set in
[Above Curr Val].
[O
u
tp
u
t
2 Confi
g]
Parameter # 91 Factory Default “Running”
[O
u
tp
u
t
2 Confi
g]
Parameter Type Read & Write
This parameter sets the condition that actuates the open
e r a 2, ermi a 19 a 20.
Units Text Settings ‘‘At Speed”
Output closes when drive reaches [Freq Command].
Th
i
s p
arame
t
er
s
e
ts th
e
cond
i
t
i
on th
a
t
a
ctu
a
t
e
s th
e
op
e
n
collector output at TB2, terminals 19 and 20.
‘‘Above Freq”
Output closes when drive exceeds value set in
[Above Freq Val].
‘‘Running”
Output closes when drive is running.
‘‘Faulted”
Output closes when drive is faulted.
‘‘Alarm”
Output closes when the drive reaches hardware
current limit, software current limit, overvoltage, line
loss or 4-20 mA loss.
‘‘Above Curr”
Output closes when current exceeds value set in
[Above Curr Val].
Application Note: During power up of the drive, the customer programmable Outputs 1 & 2 (TB2–9 & 10, TB2– 19 & 20) are in an indeterminate
state for a period of time until the internal control of the drive has initialized (3 sec. max.). Any control system connected to the programmable outputs
should take this into consideration. On power down, the programmable outputs may transition in a similar way.
- 1305 Adjustable 1
- Frequency AC Drive 1
- (Series C) 1
- PLEASE READ! 2
- IMPORTANT USER INFORMATION 2
- Summary of Changes 3
- SUMMARY OF DRIVE ENHANCEMENTS 4
- Table of Contents 7
- Appendix D – CE Conformity 8
- GENERAL PRECAUTIONS 10
- NAMEPLATE LOCATION 12
- 1305-BA03A-HAP SER C 12
- FIRMWARE COMPATIBILITY 12
- 1305 – A02 AA 13
- Information and Precautions 14
- Installation/Wiring 15
- TERMINAL BLOCK ACCESS 17
- INPUT DEVICES 19
- INPUT POWER CONDITIONING 20
- INPUT FUSING 20
- RFI FILTERING 22
- POWER WIRING 25
- P-P insulation design 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- User Side 34
- OUTPUT DEVICES 36
- CABLE TERMINATION 36
- ADAPTERS 37
- HIM DESCRIPTION 39
- HIM OPERATION 39
- Human Interface Module 40
- OFF Steady ON 41
- Steady ON OFF 41
- Flashing Steady ON 41
- Steady ON Flashing 41
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- OPERATOR LEVEL 44
- MODE LEVEL 44
- GROUP LEVEL 44
- PARAMETER LEVEL 44
- PROGRAM AND DISPLAY MODES 45
- Accel Time 46
- 99.9 Secs 46
- Choose Group 46
- Adapter 4 47
- X1111111 47
- PROCESS MODE 48
- Choose Mode 49
- Process Text 1 49
- EEPROM MODE 50
- EEPROM MODE (continued) 51
- CONTROL STATUS MODE 54
- PASSWORD MODE 56
- PASSWORD MODE (continued) 57
- Start-Up 60
- DESCRIPTION 61
- HIM DISPLAY 61
- Bul. 1305 Drive 62
- Connection Fail 62
- Open Enable Signal 65
- Restore Enable Signal 65
- Remove ALL Power 67
- Reconnect Motor 67
- Slowly Increase Speed 69
- PROGRAMMING EXAMPLE 73
- Metering Group (continued) 75
- 5-2 & 5-3 77
- Setup Group (continued) 78
- Figure 5.10 Start/Run Boost 88
- Figure 5.12 Analog Invert 90
- Two times 97
- [Skip Freq Band] 97
- Programming 100
- (continued) 100
- Figure 5.16 S-Curve 102
- Figure 5.17 S-Curve Time 103
- [( )])( )( 104
- Faults Group (continued) 109
- Diagnostics Group (continued) 112
- Masks Group (continued) 117
- Owners Group (continued) 120
- CHAPTER OBJECTIVES 126
- FAULT INFORMATION 126
- (continued) 129
- Appendix 138
- Table A.1 Specifications 139
- Serial Communications 144
- LOGIC CONTROL DATA 145
- DRIVE STATUS DATA 145
- SCALE FACTOR CONVERSION 145
- 25% of DRV 149
- 20% of DRC 149
- Drive Accessories 160
- ➀ Input reactor only 161
- CE Conformity 162
- ELECTRICAL CONFIGURATION 164
- GROUNDING 164
- CUT ALONG DOTTED LINE 170
Související produkty a manuály pro Čtečky čárových kódů Allen-Bradley 2-D
(24 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.050 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce