Allen-Bradley 2-D Uživatelský manuál Strana 128
- Strana / 172
- Tabulka s obsahem
- KNIHY
Hodnocené. / 5. Na základě hodnocení zákazníků
Troubleshooting and Fault Information
6-3
Table 6.B 1305 Fault Descriptions
Name & Fault Number
Description Action to Take
Diag C Lim FauIt
F36
The drive output current has exceeded the software [Current
Limit] and the [Cur Lim Trip En] parameter was enabled.
Check programming of [Curr Lim Trip En] parameter. Check
for excess load, improper DC boost setting, DC brake volts set
too high or other causes of excess current.
Drive → HIM The checksum read from the HIM’s EEPROM does not match the
checksum calculated from the EEPROM data.
Repeat operation. Replace HIM.
Drive Reset FauIt
F22
Occurs on power-up. Caused by having the Start Input (or Run
Input) closed, with the Stop Input open and [Run On Power Up]
= Disabled.
Check stop connection at TB2, terminal 8.
EEprom Fault
F32
EEPROM has invalid data or can not be programmed to valid
data.
Check cable connection from main control board to power board.
Reset to Default Parameters and Cycle power.
Hz Err Fault
F29
This fault indicates that there is not a valid operating frequency.
It can be caused by any of the following:
1. [Maximum Frequency] is less than [Minimum Freq].
2. i req e ie a i a wi eimi a e a era i
1. Check [Minimum Freq] and [Maximum Freq] parameters.
2. Check [Skip Freq 1], [Skip Freq 2], [Skip Freq 3] and
[Skip Freq Band] parameters.
3. e r r e wire , e e i r ra er
2.
Sk
i
p f
req
u
e
nc
ie
s
a
nd sk
i
p b
a
nd
wi
dth
e
l
imi
n
a
t
e
a
ll op
era
t
i
ng
frequencies.
3. 4-20mA input signal speed reference has been lost or is out
of range and [4-20mA Loss Sel] is set for ‘‘Stop-Fault.”
3.
Ch
e
ck fo
r
b
r
ok
e
n
wire
s
,
loos
e
conn
e
ct
i
ons o
r
t
ra
nsduc
er
loss at 4-20mA input, TB2.
Hz Sel Fault
F30
An adapter that is not connected has been chosen as the active
frequency source.
Connect proper adapter or change active frequency source.
- 1305 Adjustable 1
- Frequency AC Drive 1
- (Series C) 1
- PLEASE READ! 2
- IMPORTANT USER INFORMATION 2
- Summary of Changes 3
- SUMMARY OF DRIVE ENHANCEMENTS 4
- Table of Contents 7
- Appendix D – CE Conformity 8
- GENERAL PRECAUTIONS 10
- NAMEPLATE LOCATION 12
- 1305-BA03A-HAP SER C 12
- FIRMWARE COMPATIBILITY 12
- 1305 – A02 AA 13
- Information and Precautions 14
- Installation/Wiring 15
- TERMINAL BLOCK ACCESS 17
- INPUT DEVICES 19
- INPUT POWER CONDITIONING 20
- INPUT FUSING 20
- RFI FILTERING 22
- POWER WIRING 25
- P-P insulation design 27
- DRIVE OPERATION WITHOUT A 31
- HUMAN INTERFACE MODULE (HIM) 31
- CONTROL WIRING 31
- User Side 34
- OUTPUT DEVICES 36
- CABLE TERMINATION 36
- ADAPTERS 37
- HIM DESCRIPTION 39
- HIM OPERATION 39
- Human Interface Module 40
- OFF Steady ON 41
- Steady ON OFF 41
- Flashing Steady ON 41
- Steady ON Flashing 41
- HIM REMOVAL AND INSTALLATION 42
- HIM MODES 43
- OPERATOR LEVEL 44
- MODE LEVEL 44
- GROUP LEVEL 44
- PARAMETER LEVEL 44
- PROGRAM AND DISPLAY MODES 45
- Accel Time 46
- 99.9 Secs 46
- Choose Group 46
- Adapter 4 47
- X1111111 47
- PROCESS MODE 48
- Choose Mode 49
- Process Text 1 49
- EEPROM MODE 50
- EEPROM MODE (continued) 51
- CONTROL STATUS MODE 54
- PASSWORD MODE 56
- PASSWORD MODE (continued) 57
- Start-Up 60
- DESCRIPTION 61
- HIM DISPLAY 61
- Bul. 1305 Drive 62
- Connection Fail 62
- Open Enable Signal 65
- Restore Enable Signal 65
- Remove ALL Power 67
- Reconnect Motor 67
- Slowly Increase Speed 69
- PROGRAMMING EXAMPLE 73
- Metering Group (continued) 75
- 5-2 & 5-3 77
- Setup Group (continued) 78
- Figure 5.10 Start/Run Boost 88
- Figure 5.12 Analog Invert 90
- Two times 97
- [Skip Freq Band] 97
- Programming 100
- (continued) 100
- Figure 5.16 S-Curve 102
- Figure 5.17 S-Curve Time 103
- [( )])( )( 104
- Faults Group (continued) 109
- Diagnostics Group (continued) 112
- Masks Group (continued) 117
- Owners Group (continued) 120
- CHAPTER OBJECTIVES 126
- FAULT INFORMATION 126
- (continued) 129
- Appendix 138
- Table A.1 Specifications 139
- Serial Communications 144
- LOGIC CONTROL DATA 145
- DRIVE STATUS DATA 145
- SCALE FACTOR CONVERSION 145
- 25% of DRV 149
- 20% of DRC 149
- Drive Accessories 160
- ➀ Input reactor only 161
- CE Conformity 162
- ELECTRICAL CONFIGURATION 164
- GROUNDING 164
- CUT ALONG DOTTED LINE 170
Související produkty a manuály pro Čtečky čárových kódů Allen-Bradley 2-D
(24 stránky)© 2020, manymanuals.cz. Všechna práva vyhrazena. | 0.116 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Komentáře k této Příručce